Flexispot Standing Desk Review …Used Flexispot Riser…
Cons: What I Didn’t Like About the Flexispot E7
The cons on this desk are very little, here are a couple of features that I wasn’t always a big fan of:
The plan that the desk was available in was heavy, so bringing it inside was a group effort, however this is simply a repercussion of how durable the Flexispot is.
The practical cable tray was a bit complicated to install. In the end, you eventually slip it under screws, which wasn’t extremely clear from the guidelines.
You will need to buy an anti-fatigue mat to stay comfortable, however this is a good concept for any standing desks, so I can’t fault Flexispot for that.
When it arrived and I saw how heavy it was, I was both excited (because this indicated it was going to be sturdy) and also a little reluctant (because all of us know how much of a challenge putting together furniture can be).
The good news is, with the help of an educational YouTube link, it took me just around 42 minutes to put together. Scratch that, it took my 11-year-old daughter, with some guidance from me, from start to finish. The only problem I have with assembly was the cable television tray, which I found wasn’t discussed well in the directions.
As soon as assembled, I like the smooth look of this desk. I’m confident any of the many diverse surfaces that it can be found in would look fantastic in any workplace, and the adjustable width makes it simple to fit it in even the tiniest of office.
The quiet operation and height memory settings make it simple, efficient, and peaceful to switch in between sitting and standing as lot of times as you want throughout the day.
This desk is strong. It can hold up to 335 lbs even while in operation, so if you have a significant home computer (or wish to sleep on it for some reason) it has you covered. It will also equally disperse weight no matter how out of balance the weight you place on it is, it won’t wiggle or wobble.
because video is quite kitted out as the desk we’re looking at today is quite standard I tried to get as near that as I could on uplifts site with similar setups the flexi area desk we’re looking at today will run you about four hundred and 10 dollars versus six hundred and fifty for a similar desk from uplift I attempt to get as close as possible with the uplift design is in fact five inches longer however you can do a lot with five inches boom yes now for openness flexi spot did send this desk out for evaluation but as you should know by now does not impact my review in any way the desktop here is 55 inches broad 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming however it’s not shipping until the end of April at the earliest the desktop is an inch thick however it’s this standard laminate as you can possibly get doing not have even any cable television grommets for pass through the outside carton
for the desktop was not harmed in any way which is absolutely bizarre since I could shoot a 30-second b-roll montage of just the damage and defects on this desktop scuffed scraped pitted just super rough male if I had actually acquired this I ‘d have been on the phone with customer support instantly they did also managed to miss drilling the pilot holes where you can connect the control box to the desktop a great deal of having to do that myself without inadvertently drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be attaching the surface area to the frame that’s a far cry from the ingrained metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was actually quite simple the whole thing came together in about 45 minutes and despite the fact that there’s cables running to it from each component to support motorized function oddly absolutely where any sort of cable television management materials whatsoever the frame on this unit is a single motor dual phase design versus the dual motor three-stage style that comes requirement with the uplift desk this can be updated also to both the dual stage dual motor and a three-stage double motor which pushes the expense of the desk up
an additional 70 bucks the frame is designed for a max load of 154 pounds and it moves at a rate at an inch per 2nd the height can vary from simply under 28 inches to simply over forty 7 point six inches so a max I ‘d it is more than tall enough even for me and I stay at 6 foot for this model does come basic with the control board that enables up-and-down motion plus three memory areas with an LED readout to inform you the desk height the single motor style uses this drive shaft assembly which needs to be changed as the width of the desk is changed the motor operation itself while it might be slow is very peaceful as in barely audible this outside a rate would be the one advantage I would give this system over the uplift desk and I wish to take care here due to the fact that this isn’t a hit piece this desk is 240 dollars less expensive than the equivalent uplift design over 35% cheaper even if you upgrade this flexi area test to the dual motor three-stage style it still is available in a hundred and seventy dollars more affordable than the uplift but less expensive doesn’t imply cheap this desk is still over four hundred dollars if I had actually paid over $400 for this desk I ‘d have a problem with that the front to back stability of this desk is strong even if max height I’ll certainly give it that but the lateral stability of this desk the horizontal motion at this cost point it’s undesirable it’s rub salt in the wound here they include a little security baffle this little steel piece that mounts to the frame and covers a portion of this rotating driveshaft when
this desk sees any lateral movement at all the drive shaft strikes the noise and this baffle is absolutely infuriating to top things off I chose to add rolling casters to this desk this was a $30 upgrade and 2 of those 4 casters got here damaged also my prepare for this desk at this moment is to lose the desk top and came with all together and change it with a white laminate lemon table from Ikea and use it as an adjustable photo table which you can’t do this frame will accommodate desktops approximately 63 inches wide and 31 and a half inches deep so this will roll around the studio make it simpler to movie items without needing to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift initially that is a financial investment in quality workplace furnishings that will last you this at best seems like a more affordable imitation of that it just doesn’t feel quality and the difference in between this desk and my primary desk is night and day do feel free to check out their website as well which likewise feels eerily similar to one of their rivals there’s a wealth of accessories you can get for the flexi spot desk as much as and consisting of a foot massager and even a stationary stationary bicycle and I might invest another 10 minutes of our precious time covering different options and devices I might however I think I’m better that they just sent out a standard desk due to the fact that as a basic desk I’m not a fan of the quality assurance at this rate point and I don’t believe slapping on a lot of bonus is the relocation when the core item isn’t what it should be they do use a 30-day trial if you’re just morbidly curious and they service warranty their desks for three years extremely desk is five years and uplift desk is 7 years if you are Used Flexispot Riser
in the market for a sit-stand desk they’re incredible mine’s been a life changer for me both in terms of gaming and productivity however I would spend the additional money it’s gon na require to get into a greater end manufacturer like uplift desk or very desk and I have not personally used very desk items so I can’t speak on it however their credibility is very good huge thanks to flexi spot for sending this out for review unfortunately I can not advise this unit and for the record I’m a hundred percent sure they would have happily replaced the parts that I had a concern with seeing as how both the desktop and the casters got here damaged but from a customer viewpoint you ‘d most likely be actually delighted to get this in