Flexispot Standing Desk Evaluation …Flexispot Standing Desk 41…
Cons: What I Didn’t Like About the Flexispot E7
The cons on this desk are very little, here are a couple of features that I wasn’t always a substantial fan of:
The plan that the desk was available in was heavy, so bringing it inside was a group effort, but this is simply a repercussion of how sturdy the Flexispot is.
The practical cable tray was a little bit confusing to set up. In the end, you eventually slip it under screws, which wasn’t really clear from the instructions.
You will need to purchase an anti-fatigue mat to remain comfortable, but this is a good idea for any standing desks, so I can’t fault Flexispot for that.
When it arrived and I saw how heavy it was, I was both fired up (since this indicated it was going to be durable) and also a little reluctant (because we all know how much of a challenge putting together furniture can be).
The good news is, with the help of an instructional YouTube link, it took me just around 42 minutes to assemble. Scratch that, it took my 11-year-old daughter, with some guidance from me, from start to finish. The only problem I have with assembly was the cable tray, which I discovered wasn’t explained well in the guidelines.
As soon as put together, I enjoy the streamlined appearance of this desk. I’m confident any of the many diverse surfaces that it comes in would look fantastic in any workplace, and the adjustable width makes it easy to fit it in even the tiniest of home offices.
The quiet operation and height memory settings make it simple, effective, and peaceful to change between sitting and standing as often times as you want throughout the day.
This desk is durable. It can hold up to 335 lbs even while in operation, so if you have a hefty home computer (or wish to take a nap on it for some reason) it has you covered. It will likewise evenly distribute weight no matter how out of balance the weight you place on it is, it won’t wobble or wiggle.
in that video is pretty kitted out as the desk we’re taking a look at today is pretty fundamental I tried to get as near that as I might on uplifts site with equivalent configurations the flexi spot desk we’re looking at today will run you about four hundred and 10 dollars versus 6 hundred and fifty for a similar desk from uplift I attempt to get as close as possible with the uplift design is in fact five inches longer but you can do a lot with five inches boom yes now for transparency flexi area did send this desk out for review however as you should understand by now does not affect my review in any way the desktop here is 55 inches wide 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming however it’s not delivering till completion of April at the earliest the desktop is an inch thick but it’s this standard laminate as you can potentially get lacking even any cable television grommets for pass through the outside carton
for the desktop was not damaged in any way which is absolutely unusual since I might shoot a 30-second b-roll montage of simply the damage and defects on this desktop scuffed scraped pitted simply extremely rough male if I had acquired this I ‘d have been on the phone with customer service immediately they did likewise handled to miss out on drilling the pilot holes where you can attach the control box to the desktop a lot of needing to do that myself without accidentally drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be attaching the surface area to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from needing to drill that top was really pretty simple the entire thing came together in about 45 minutes and despite the fact that there’s cables going to it from each element to support motorized function oddly definitely where any type of cable television management materials whatsoever the frame on this system is a single motor double stage style versus the dual motor three-stage style that comes standard with the uplift desk this can be updated as well to both the dual stage dual motor and a three-stage dual motor which pushes the expense of the desk up
an additional 70 bucks the frame is created for a max load of 154 pounds and it moves at a rate at an inch per second the height can range from simply under 28 inches to simply over forty 7 point six inches so a max I ‘d it is more than tall adequate even for me and I remain at 6 foot for this design does come standard with the control board that allows for up-and-down motion plus three memory areas with an LED readout to inform you the desk height the single motor style uses this drive shaft assembly which needs to be changed as the width of the desk is adjusted the motor operation itself while it might be sluggish is very quiet as in barely audible this outside a cost would be the one benefit I would give this system over the uplift desk and I want to beware here due to the fact that this isn’t a hit piece this desk is 240 dollars cheaper than the comparable uplift model over 35% more affordable even if you update this flexi spot test to the double motor three-stage design it still can be found in a hundred and seventy dollars more affordable than the uplift however more affordable does not imply cheap this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have a problem with that the front to back stability of this desk is strong even if max height I’ll absolutely provide it that however the lateral stability of this desk the horizontal movement at this price point it’s inappropriate it’s add insult to injury here they consist of a little safety baffle this little steel piece that mounts to the frame and covers a part of this turning driveshaft when
this desk sees any lateral movement at all the drive shaft hits the sound and this baffle is absolutely infuriating to top things off I chose to include rolling casters to this desk this was a $30 upgrade and 2 of those four casters arrived harmed also my prepare for this desk at this moment is to lose the desk top and featured all together and replace it with a white laminate lemon table from Ikea and utilize it as an adjustable image table which you can’t do this frame will accommodate desktops up to 63 inches broad and 31 and a half inches deep so this will roll around the studio make it much easier to film items without having to adjust complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift first that is an investment in quality workplace furniture that will last you this at best feels like a less expensive imitation of that it just doesn’t feel quality and the difference between this desk and my primary desk is night and day do do not hesitate to have a look at their website also which also feels eerily comparable to one of their rivals there’s a wealth of accessories you can get for the flexi area desk as much as and consisting of a foot massager and even a stationary exercise bike and I could spend another 10 minutes of our precious time covering various options and accessories I could however I think I’m better that they only sent out a fundamental desk since as a standard desk I’m not a fan of the quality control at this cost point and I don’t believe slapping on a bunch of extras is the relocation when the core product isn’t what it must be they do provide a 30-day trial if you’re simply morbidly curious and they guarantee their desks for 3 years very desk is 5 years and uplift desk is 7 years if you are Flexispot Standing Desk 41
in the market for a sit-stand desk they’re fantastic mine’s been a life changer for me both in regards to gaming and efficiency but I would spend the money it’s gon na require to get into a greater end manufacturer like uplift desk or really desk and I have not personally utilized very desk products so I can’t speak on it but their track record is great huge thanks to flexi area for sending this out for evaluation unfortunately I can not suggest this unit and for the record I’m a hundred percent sure they would have gladly replaced the parts that I had a problem with viewing as how both the desktop and the casters showed up harmed but from a customer viewpoint you ‘d probably be really excited to get this in