Flexispot Standing Desk Review …Flexispot Monitor Stand Workstation…
Cons: What I Didn’t Like About the Flexispot E7
The cons on this desk are minimal, here are a few functions that I wasn’t always a huge fan of:
The package that the desk can be found in was heavy, so bringing it inside was a group effort, but this is just a consequence of how sturdy the Flexispot is.
The convenient cable tray was a little bit complicated to install. In the end, you ultimately slip it under screws, which wasn’t very clear from the directions.
You will require to purchase an anti-fatigue mat to remain comfy, but this is a good idea for any standing desks, so I can’t fault Flexispot for that.
When it got here and I saw how heavy it was, I was both thrilled (since this suggested it was going to be durable) and also a little hesitant (since all of us understand just how much of a challenge assembling furniture can be).
Luckily, with the help of a training YouTube link, it took me just around 42 minutes to put together. Scratch that, it took my 11-year-old daughter, with some guidance from me, from start to finish. The only hang-up I have with assembly was the cable tray, which I found wasn’t discussed well in the directions.
Once put together, I love the sleek appearance of this desk. I’m positive any of the many diverse finishes that it can be found in would look great in any workplace, and the adjustable width makes it simple to fit it in even the tiniest of office.
The quiet operation and height memory settings make it easy, efficient, and peaceful to change in between sitting and standing as often times as you desire throughout the day.
This desk is strong. It can hold up to 335 lbs even while in operation, so if you have a hefty desktop (or want to rest on it for some reason) it has you covered. It will also uniformly distribute weight no matter how out of balance the weight you place on it is, it won’t wobble or wiggle.
in that video is pretty kitted out as the desk we’re taking a look at today is pretty standard I tried to get as close to that as I could on uplifts website with equivalent setups the flexi spot desk we’re looking at today will run you about four hundred and 10 dollars versus 6 hundred and fifty for a comparable desk from uplift I attempt to get as close as possible with the uplift model is in fact five inches longer however you can do a lot with 5 inches boom yes now for openness flexi area did send this desk out for evaluation however as you should know by now does not impact my review in any way the desktop here is 55 inches broad 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming however it’s not shipping until the end of April at the earliest the desktop is an inch thick but it’s this basic laminate as you can potentially get lacking even any cable grommets for pass through the outside container
for the desktop was not damaged in any way which is utterly bizarre since I might shoot a 30-second b-roll montage of simply the damage and flaws on this desktop scuffed scraped pitted just extremely rough male if I had purchased this I ‘d have been on the phone with client service right away they did likewise managed to miss out on drilling the pilot holes where you can connect the control box to the desktop a lot of needing to do that myself without accidentally drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be attaching the surface to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was actually quite uncomplicated the whole thing came together in about 45 minutes and despite the fact that there’s cables going to it from each element to support motorized function strangely definitely where any type of cable management products whatsoever the frame on this unit is a single motor double stage style versus the dual motor three-stage design that comes standard with the uplift desk this can be updated too to both the dual stage dual motor and a three-stage double motor which presses the expense of the desk up
an extra 70 dollars the frame is created for a max load of 154 pounds and it moves at a rate at an inch per 2nd the height can range from just under 28 inches to just over forty 7 point six inches so a max I ‘d it is more than tall sufficient even for me and I remain at 6 foot for this design does come standard with the control board that allows for up-and-down movement plus 3 memory spots with an LED readout to inform you the desk height the single motor style utilizes this drive shaft assembly which has to be adjusted as the width of the desk is adjusted the motor operation itself while it might be sluggish is very quiet as in barely audible this outside a cost would be the one advantage I would offer this system over the uplift desk and I wish to beware here since this isn’t a hit piece this desk is 240 dollars more affordable than the comparable uplift model over 35% less expensive even if you upgrade this flexi spot test to the dual motor three-stage style it still can be found in a hundred and seventy dollars less expensive than the uplift but more affordable does not imply inexpensive this desk is still over four hundred dollars if I had actually paid over $400 for this desk I ‘d have a problem with that the front to back stability of this desk is solid even if max height I’ll definitely provide it that however the lateral stability of this desk the horizontal motion at this cost point it’s inappropriate it’s rub salt in the wound here they include a little security baffle this little steel piece that mounts to the frame and covers a part of this rotating driveshaft when
this desk sees any lateral motion at all the drive shaft hits this baffle and the sound is definitely frustrating to leading things off I decided to include rolling casters to this desk this was a $30 upgrade and 2 of those 4 casters showed up harmed also my prepare for this desk at this point is to lose the desk top and featured entirely and change it with a white laminate lemon table from Ikea and use it as an adjustable picture table which you can’t do this frame will accommodate desktops as much as 63 inches wide and 31 and a half inches deep so this will roll around the studio make it simpler to movie items without needing to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift initially that is a financial investment in quality office furnishings that will last you this at finest seems like a less expensive replica of that it just doesn’t feel quality and the difference in between this desk and my main desk is night and day do do not hesitate to take a look at their website also which also feels eerily comparable to among their rivals there’s a wealth of devices you can get for the flexi area desk as much as and consisting of a foot massager and even a stationary exercise bike and I could invest another 10 minutes of our valuable time covering different choices and devices I could however I believe I’m better that they just sent out a standard desk due to the fact that as a fundamental desk I’m not a fan of the quality assurance at this cost point and I do not believe slapping on a bunch of extras is the relocation when the core product isn’t what it need to be they do use a 30-day trial if you’re simply morbidly curious and they service warranty their desks for three years extremely desk is five years and uplift desk is seven years if you are Flexispot Monitor Stand Workstation
in the market for a sit-stand desk they’re amazing mine’s been a life changer for me both in terms of video gaming and efficiency but I would spend the money it’s gon na take to enter a higher end manufacturer like uplift desk or extremely desk and I haven’t personally utilized very desk items so I can’t speak on it but their track record is excellent huge thanks to flexi area for sending this out for evaluation sadly I can not suggest this unit and for the record I’m a hundred percent sure they would have happily changed the parts that I had a problem with viewing as how both the desktop and the casters got here harmed but from a client perspective you ‘d most likely be really excited to get this in