Flexispot Standing Desk Review …Flexispot Ep4…
Cons: What I Didn’t Like About the Flexispot E7
The cons on this desk are very little, here are a couple of features that I wasn’t always a big fan of:
The package that the desk can be found in was heavy, so bringing it inside was a group effort, however this is just a consequence of how durable the Flexispot is.
The practical cable television tray was a bit complicated to set up. In the end, you ultimately slip it under screws, which wasn’t extremely clear from the guidelines.
You will need to purchase an anti-fatigue mat to stay comfy, however this is a good idea for any standing desks, so I can’t fault Flexispot for that.
When it got here and I saw how heavy it was, I was both excited (considering that this indicated it was going to be durable) and also a little reluctant (because we all know just how much of a difficulty putting together furnishings can be).
The good news is, with the help of an educational YouTube link, it took me just around 42 minutes to assemble. Scratch that, it took my 11-year-old child, with some guidance from me, from start to finish. The only problem I have with assembly was the cable television tray, which I found wasn’t described well in the instructions.
As soon as assembled, I love the smooth appearance of this desk. I’m confident any of the many diverse surfaces that it is available in would look great in any workplace, and the adjustable width makes it simple to fit it in even the tiniest of home offices.
The quiet operation and height memory settings make it simple, efficient, and quiet to change in between sitting and standing as many times as you desire throughout the day.
This desk is tough. It can hold up to 335 lbs even while in operation, so if you have a large desktop computer (or want to take a nap on it for some reason) it has you covered. It will likewise evenly distribute weight no matter how unbalanced the weight you put on it is, it won’t wiggle or wobble.
because video is quite kitted out as the desk we’re taking a look at today is quite standard I attempted to get as close to that as I could on uplifts site with equivalent setups the flexi spot desk we’re taking a look at today will run you about four hundred and ten dollars versus six hundred and fifty for a similar desk from uplift I try to get as close as possible with the uplift model is actually 5 inches longer however you can do a lot with 5 inches boom yes now for openness flexi area did send this desk out for evaluation but as you must know by now doesn’t impact my evaluation in any way the desktop here is 55 inches large 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not shipping till the end of April at the earliest the desktop is an inch thick however it’s this fundamental laminate as you can perhaps get lacking even any cable television grommets for go through the outside carton
for the desktop was not damaged in any way which is entirely bizarre since I might shoot a 30-second b-roll montage of just the damage and flaws on this desktop scuffed scraped pitted simply extremely rough male if I had actually acquired this I ‘d have been on the phone with customer support immediately they did also handled to miss drilling the pilot holes where you can attach the control box to the desktop a great deal of needing to do that myself without mistakenly drilling through the opposite of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface area to the frame that’s a far cry from the ingrained metal inserts that we saw on the uplift desk so assembly aside from needing to drill that top was really pretty simple the whole thing came together in about 45 minutes and despite the fact that there’s cables going to it from each element to support motorized function unusually definitely where any sort of cable television management materials whatsoever the frame on this system is a single motor double stage style versus the dual motor three-stage design that comes standard with the uplift desk this can be updated too to both the double phase double motor and a three-stage dual motor which presses the cost of the desk up
an extra 70 dollars the frame is developed for a max load of 154 pounds and it moves at a rate at an inch per second the height can vary from simply under 28 inches to simply over forty seven point 6 inches so a max I ‘d it is more than high adequate even for me and I remain at 6 foot for this design does come basic with the control board that permits up-and-down motion plus 3 memory areas with an LED readout to tell you the desk height the single motor style uses this drive shaft assembly which has to be adjusted as the width of the desk is changed the motor operation itself while it might be sluggish is extremely quiet as in barely audible this outside a cost would be the one benefit I would offer this unit over the uplift desk and I want to be careful here because this isn’t a hit piece this desk is 240 dollars more affordable than the similar uplift design over 35% more affordable even if you upgrade this flexi area test to the dual motor three-stage style it still can be found in a hundred and seventy dollars cheaper than the uplift however less expensive does not suggest cheap this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is solid even if max height I’ll definitely offer it that however the lateral stability of this desk the horizontal movement at this price point it’s undesirable it’s add insult to injury here they consist of a little security baffle this little steel piece that mounts to the frame and covers a part of this turning driveshaft when
this desk sees any lateral movement at all the drive shaft hits this baffle and the sound is definitely shocking to top things off I chose to add rolling casters to this desk this was a $30 upgrade and two of those 4 casters arrived harmed too my prepare for this desk at this point is to lose the desk top and came with all together and change it with a white laminate lemon table from Ikea and utilize it as an adjustable picture table which you can’t do this frame will accommodate desktops approximately 63 inches broad and 31 and a half inches deep so this will roll around the studio make it easier to film items without having to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift first that is a financial investment in quality office furniture that will last you this at finest seems like a more affordable replica of that it just does not feel quality and the distinction between this desk and my primary desk is night and day do do not hesitate to check out their website too which likewise feels eerily comparable to one of their competitors there’s a wealth of accessories you can get for the flexi area desk as much as and consisting of a foot massager and even a stationary stationary bicycle and I might spend another 10 minutes of our valuable time covering different alternatives and accessories I might however I think I’m happier that they just sent out a fundamental desk because as a basic desk I’m not a fan of the quality control at this price point and I do not think slapping on a lot of bonus is the move when the core product isn’t what it ought to be they do use a 30-day trial if you’re simply morbidly curious and they warranty their desks for three years extremely desk is five years and uplift desk is 7 years if you are Flexispot Ep4
in the market for a sit-stand desk they’re fantastic mine’s been a life changer for me both in regards to video gaming and productivity but I would invest the money it’s gon na take to enter into a higher end manufacturer like uplift desk or extremely desk and I haven’t personally utilized really desk items so I can’t speak on it however their reputation is very good huge thanks to flexi spot for sending this out for review sadly I can not recommend this unit and for the record I’m a hundred percent sure they would have happily changed the parts that I had a concern with viewing as how both the desktop and the casters got here harmed but from a customer viewpoint you ‘d probably be actually excited to get this in