Flexispot Standing Desk Review …Flexispot E1 Height Adjustable Desk…
Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are minimal, here are a few functions that I wasn’t always a huge fan of:
The plan that the desk was available in was heavy, so bringing it inside was a group effort, however this is simply an effect of how durable the Flexispot is.
The practical cable television tray was a little bit confusing to set up. In the end, you ultimately slip it under screws, which wasn’t extremely clear from the directions.
You will need to buy an anti-fatigue mat to remain comfortable, however this is a good concept for any standing desks, so I can’t fault Flexispot for that.
When it showed up and I saw how heavy it was, I was both fired up (since this implied it was going to be durable) and likewise a little reluctant (because all of us know just how much of an obstacle putting together furnishings can be).
The good news is, with the help of an educational YouTube link, it took me just around 42 minutes to put together. Scratch that, it took my 11-year-old child, with some supervision from me, from start to finish. The only problem I have with assembly was the cable tray, which I discovered wasn’t explained well in the directions.
When assembled, I like the sleek look of this desk. I’m positive any of the many varied finishes that it comes in would look great in any workplace, and the adjustable width makes it easy to fit it in even the smallest of home offices.
The peaceful operation and height memory settings make it easy, efficient, and peaceful to switch in between sitting and standing as often times as you desire throughout the day.
This desk is sturdy. It can hold up to 335 pounds even while in operation, so if you have a significant desktop (or want to take a nap on it for some reason) it has you covered. It will also evenly disperse weight no matter how out of balance the weight you put on it is, it will not wiggle or wobble.
because video is quite kitted out as the desk we’re taking a look at today is pretty basic I tried to get as close to that as I could on uplifts website with equivalent setups the flexi spot desk we’re looking at today will run you about four hundred and ten dollars versus six hundred and fifty for a similar desk from uplift I attempt to get as close as possible with the uplift model is in fact 5 inches longer however you can do a lot with 5 inches boom yes now for transparency flexi spot did send this desk out for evaluation but as you need to know by now doesn’t impact my evaluation in any way the desktop here is 55 inches large 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not shipping till completion of April at the earliest the desktop is an inch thick however it’s this fundamental laminate as you can possibly get doing not have even any cable television grommets for pass through the outdoors carton
for the desktop was not damaged in any way which is entirely strange because I might shoot a 30-second b-roll montage of simply the damage and defects on this desktop scuffed scraped pitted simply extremely rough man if I had actually acquired this I ‘d have been on the phone with client service right away they did also managed to miss out on drilling the pilot holes where you can connect the control box to the desktop a great deal of having to do that myself without inadvertently drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface area to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was really pretty simple the whole thing came together in about 45 minutes and despite the fact that there’s cables running to it from each part to support motorized function strangely definitely where any sort of cable television management materials whatsoever the frame on this system is a single motor double phase style versus the dual motor three-stage design that comes requirement with the uplift desk this can be upgraded too to both the double phase dual motor and a three-stage dual motor which presses the expense of the desk up
an extra 70 dollars the frame is developed for a max load of 154 pounds and it moves at a rate at an inch per second the height can range from just under 28 inches to just over forty seven point six inches so a max I ‘d it is more than high enough even for me and I stay at 6 foot for this design does come standard with the control board that enables up-and-down movement plus 3 memory areas with an LED readout to tell you the desk height the single motor design utilizes this drive shaft assembly which has to be changed as the width of the desk is changed the motor operation itself while it might be slow is really peaceful as in barely audible this outside a cost would be the one benefit I would give this unit over the uplift desk and I want to beware here since this isn’t a hit piece this desk is 240 dollars more affordable than the comparable uplift design over 35% cheaper even if you upgrade this flexi area test to the dual motor three-stage style it still is available in a hundred and seventy dollars less expensive than the uplift however less expensive doesn’t suggest inexpensive this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is solid even if max height I’ll absolutely give it that but the lateral stability of this desk the horizontal movement at this price point it’s unacceptable it’s add fuel to the fire here they consist of a little safety baffle this little steel piece that installs to the frame and covers a part of this turning driveshaft when
this desk sees any lateral motion at all the drive shaft hits the noise and this baffle is definitely frustrating to top things off I decided to include rolling casters to this desk this was a $30 upgrade and 2 of those four casters arrived damaged as well my plan for this desk at this moment is to lose the desk top and featured all together and replace it with a white laminate lemon table from Ikea and use it as an adjustable photo table which you can’t do this frame will accommodate desktops approximately 63 inches large and 31 and a half inches deep so this will roll around the studio make it easier to film items without having to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I discovered uplift first that is a financial investment in quality workplace furnishings that will last you this at best seems like a more affordable imitation of that it simply doesn’t feel quality and the distinction in between this desk and my main desk is night and day do feel free to have a look at their site also which likewise feels eerily similar to among their competitors there’s a wealth of accessories you can get for the flexi spot desk up to and including a foot massager and even a fixed exercise bike and I might invest another 10 minutes of our valuable time covering different choices and devices I might however I believe I’m happier that they just sent out a standard desk because as a fundamental desk I’m not a fan of the quality control at this cost point and I don’t believe slapping on a bunch of bonus is the move when the core item isn’t what it must be they do provide a 30-day trial if you’re simply morbidly curious and they guarantee their desks for three years extremely desk is five years and uplift desk is 7 years if you are Flexispot E1 Height Adjustable Desk
in the market for a sit-stand desk they’re remarkable mine’s been a life changer for me both in terms of gaming and performance however I would invest the additional money it’s gon na require to enter a greater end manufacturer like uplift desk or really desk and I have not personally utilized really desk products so I can’t speak on it but their track record is excellent big thanks to flexi area for sending this out for review regrettably I can not advise this unit and for the record I’m a hundred percent sure they would have gladly changed the parts that I had an issue with seeing as how both the desktop and the casters got here harmed but from a client viewpoint you ‘d probably be really delighted to get this in