Flexispot Standing Desk Review …Flexispot Bamboo Desk…
Cons: What I Didn’t Like About the Flexispot E7
The cons on this desk are minimal, here are a couple of features that I wasn’t necessarily a big fan of:
The bundle that the desk can be found in was heavy, so bringing it inside was a group effort, but this is simply an effect of how durable the Flexispot is.
The hassle-free cable television tray was a bit complicated to set up. In the end, you eventually slip it under screws, which wasn’t very clear from the directions.
You will require to buy an anti-fatigue mat to remain comfortable, but this is a great idea for any standing desks, so I can’t fault Flexispot for that.
When it got here and I saw how heavy it was, I was both fired up (because this suggested it was going to be strong) and also a little reluctant (because all of us understand just how much of a challenge assembling furniture can be).
Thankfully, with the help of an instructional YouTube link, it took me only around 42 minutes to assemble. Scratch that, it took my 11-year-old child, with some guidance from me, from start to finish. The only problem I have with assembly was the cable television tray, which I found wasn’t discussed well in the instructions.
When assembled, I like the streamlined appearance of this desk. I’m confident any of the many varied finishes that it can be found in would look fantastic in any workplace, and the adjustable width makes it simple to fit it in even the tiniest of home offices.
The quiet operation and height memory settings make it easy, efficient, and peaceful to switch between sitting and standing as lot of times as you desire throughout the day.
Finally, this desk is sturdy. It can hold up to 335 lbs even while in operation, so if you have a hefty home computer (or wish to take a nap on it for some reason) it has you covered. It will likewise equally disperse weight no matter how out of balance the weight you put on it is, it won’t wobble or wiggle.
because video is quite kitted out as the desk we’re taking a look at today is pretty basic I tried to get as near to that as I could on uplifts website with comparable setups the flexi spot desk we’re looking at today will run you about four hundred and ten dollars versus six hundred and fifty for a similar desk from uplift I try to get as close as possible with the uplift design is really five inches longer however you can do a lot with five inches boom yes now for transparency flexi area did send this desk out for review however as you should understand by now does not impact my review in any way the desktop here is 55 inches large 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not shipping till completion of April at the earliest the desktop is an inch thick but it’s this basic laminate as you can potentially get lacking even any cable grommets for go through the outside carton
for the desktop was not damaged in any way which is utterly unusual because I might shoot a 30-second b-roll montage of just the damage and defects on this desktop scuffed scraped pitted just very rough male if I had actually purchased this I ‘d have been on the phone with customer care immediately they did also managed to miss out on drilling the pilot holes where you can attach the control box to the desktop a great deal of having to do that myself without inadvertently drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface area to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was in fact pretty uncomplicated the whole thing came together in about 45 minutes and despite the fact that there’s cables running to it from each element to support motorized function unusually absolutely where any sort of cable management materials whatsoever the frame on this unit is a single motor double phase style versus the double motor three-stage style that comes requirement with the uplift desk this can be updated as well to both the double phase dual motor and a three-stage double motor which pushes the expense of the desk up
an extra 70 dollars the frame is created for a max load of 154 pounds and it moves at a rate at an inch per second the height can range from just under 28 inches to simply over forty seven point 6 inches so a max I ‘d it is more than tall enough even for me and I remain at 6 foot for this model does come standard with the control panel that permits up-and-down motion plus 3 memory areas with an LED readout to inform you the desk height the single motor style uses this drive shaft assembly which needs to be adjusted as the width of the desk is changed the motor operation itself while it might be slow is really peaceful as in barely audible this outside a rate would be the one benefit I would offer this system over the uplift desk and I want to beware here because this isn’t a hit piece this desk is 240 dollars more affordable than the comparable uplift model over 35% cheaper even if you update this flexi spot test to the double motor three-stage style it still comes in a hundred and seventy dollars less expensive than the uplift but cheaper doesn’t indicate inexpensive this desk is still over four hundred dollars if I had actually paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is strong even if max height I’ll definitely offer it that but the lateral stability of this desk the horizontal movement at this cost point it’s unacceptable it’s rub salt in the wound here they consist of a little safety baffle this little steel piece that mounts to the frame and covers a part of this rotating driveshaft when
this desk sees any lateral motion at all the drive shaft hits this baffle and the sound is absolutely infuriating to leading things off I decided to include rolling casters to this desk this was a $30 upgrade and two of those 4 casters showed up damaged also my plan for this desk at this point is to lose the desk top and came with all together and replace it with a white laminate lemon table from Ikea and utilize it as an adjustable image table which you can’t do this frame will accommodate desktops approximately 63 inches wide and 31 and a half inches deep so this will roll around the studio make it easier to film items without needing to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I discovered uplift first that is a financial investment in quality office furniture that will last you this at finest seems like a cheaper replica of that it just does not feel quality and the difference in between this desk and my main desk is night and day do do not hesitate to check out their site as well which likewise feels strangely comparable to among their rivals there’s a wealth of accessories you can get for the flexi spot desk approximately and consisting of a foot massager and even a fixed stationary bicycle and I might spend another 10 minutes of our valuable time covering numerous alternatives and devices I could but I think I’m better that they just sent out a basic desk because as a basic desk I’m not a fan of the quality assurance at this rate point and I don’t believe slapping on a bunch of additionals is the move when the core product isn’t what it need to be they do provide a 30-day trial if you’re simply morbidly curious and they warranty their desks for three years extremely desk is five years and uplift desk is seven years if you are Flexispot Bamboo Desk
in the market for a sit-stand desk they’re fantastic mine’s been a life changer for me both in terms of gaming and productivity however I would spend the additional money it’s gon na take to get into a greater end manufacturer like uplift desk or very desk and I have not personally used really desk items so I can’t speak on it but their track record is great huge thanks to flexi spot for sending this out for evaluation regrettably I can not recommend this unit and for the record I’m a hundred percent sure they would have happily changed the parts that I had an issue with viewing as how both the desktop and the casters showed up damaged however from a customer perspective you ‘d probably be truly thrilled to get this in