Flexispot Standing Desk Evaluation …Flexispot 55 X 28 Inches Electric Stand Up Desk Workstation…
Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are minimal, here are a couple of features that I wasn’t necessarily a substantial fan of:
The bundle that the desk was available in was heavy, so bringing it inside was a group effort, however this is simply a repercussion of how strong the Flexispot is.
The practical cable tray was a bit confusing to install. In the end, you ultimately slip it under screws, which wasn’t extremely clear from the guidelines.
You will require to purchase an anti-fatigue mat to stay comfy, however this is a good concept for any standing desks, so I can’t fault Flexispot for that.
When it arrived and I saw how heavy it was, I was both thrilled (because this meant it was going to be strong) and also a little reluctant (since we all know how much of an obstacle putting together furnishings can be).
Luckily, with the help of an instructional YouTube link, it took me just around 42 minutes to put together. Scratch that, it took my 11-year-old daughter, with some guidance from me, from start to finish. The only problem I have with assembly was the cable tray, which I found wasn’t discussed well in the instructions.
As soon as assembled, I like the smooth look of this desk. I’m confident any of the many varied surfaces that it is available in would look excellent in any workplace, and the adjustable width makes it easy to fit it in even the smallest of home offices.
The quiet operation and height memory settings make it easy, efficient, and peaceful to change between sitting and standing as often times as you want throughout the day.
Finally, this desk is strong. It can hold up to 335 lbs even while in operation, so if you have a large home computer (or wish to rest on it for some reason) it has you covered. It will also evenly distribute weight no matter how out of balance the weight you place on it is, it won’t wobble or wiggle.
in that video is quite kitted out as the desk we’re looking at today is quite standard I attempted to get as near to that as I could on uplifts site with similar configurations the flexi area desk we’re taking a look at today will run you about four hundred and 10 dollars versus 6 hundred and fifty for a similar desk from uplift I try to get as close as possible with the uplift model is really 5 inches longer but you can do a lot with five inches boom yes now for openness flexi area did send this desk out for evaluation but as you should know by now doesn’t impact my review in any way the desktop here is 55 inches wide 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not shipping up until the end of April at the earliest the desktop is an inch thick but it’s this fundamental laminate as you can possibly get doing not have even any cable grommets for travel through the outside carton
for the desktop was not damaged in any way which is utterly unusual since I might shoot a 30-second b-roll montage of simply the damage and defects on this desktop scuffed scraped pitted simply extremely rough man if I had purchased this I ‘d have been on the phone with customer care right away they did likewise managed to miss drilling the pilot holes where you can attach the control box to the desktop a lot of needing to do that myself without inadvertently drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface to the frame that’s a far cry from the ingrained metal inserts that we saw on the uplift desk so assembly aside from needing to drill that top was actually quite straightforward the entire thing came together in about 45 minutes and despite the fact that there’s cables going to it from each part to support motorized function unusually absolutely where any sort of cable television management products whatsoever the frame on this unit is a single motor dual phase design versus the double motor three-stage style that comes standard with the uplift desk this can be upgraded also to both the dual phase dual motor and a three-stage double motor which pushes the cost of the desk up
an extra 70 dollars the frame is designed for a max load of 154 pounds and it moves at a rate at an inch per 2nd the height can vary from just under 28 inches to just over forty 7 point 6 inches so a max I ‘d it is more than high enough even for me and I remain at 6 foot for this model does come standard with the control board that allows for up-and-down motion plus three memory spots with an LED readout to tell you the desk height the single motor style uses this drive shaft assembly which needs to be changed as the width of the desk is changed the motor operation itself while it might be sluggish is very quiet as in barely audible this outside a cost would be the one benefit I would give this system over the uplift desk and I want to take care here because this isn’t a hit piece this desk is 240 dollars cheaper than the similar uplift design over 35% more affordable even if you update this flexi area test to the dual motor three-stage style it still is available in a hundred and seventy dollars more affordable than the uplift but cheaper does not suggest inexpensive this desk is still over four hundred dollars if I had actually paid over $400 for this desk I ‘d have a problem with that the front to back stability of this desk is strong even if max height I’ll certainly provide it that but the lateral stability of this desk the horizontal movement at this rate point it’s inappropriate it’s rub salt in the wound here they consist of a little safety baffle this little steel piece that mounts to the frame and covers a portion of this rotating driveshaft when
this desk sees any lateral movement at all the drive shaft strikes the sound and this baffle is definitely infuriating to top things off I chose to add rolling casters to this desk this was a $30 upgrade and 2 of those 4 casters got here harmed also my plan for this desk at this moment is to lose the desk top and came with completely and change it with a white laminate lemon table from Ikea and utilize it as an adjustable picture table which you can’t do this frame will accommodate desktops as much as 63 inches wide and 31 and a half inches deep so this will roll around the studio make it simpler to movie items without having to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift first that is an investment in quality workplace furniture that will last you this at best seems like a more affordable replica of that it just doesn’t feel quality and the difference between this desk and my primary desk is night and day do do not hesitate to check out their website too which likewise feels strangely similar to one of their competitors there’s a wealth of devices you can get for the flexi area desk approximately and including a foot massager and even a fixed exercise bike and I could invest another 10 minutes of our precious time covering different alternatives and accessories I could but I believe I’m happier that they just sent a standard desk because as a fundamental desk I’m not a fan of the quality assurance at this price point and I don’t think slapping on a bunch of bonus is the relocation when the core item isn’t what it should be they do offer a 30-day trial if you’re simply morbidly curious and they warranty their desks for 3 years extremely desk is five years and uplift desk is 7 years if you are Flexispot 55 X 28 Inches Electric Stand Up Desk Workstation
in the market for a sit-stand desk they’re fantastic mine’s been a life changer for me both in regards to video gaming and productivity however I would spend the money it’s gon na take to get into a higher end producer like uplift desk or really desk and I haven’t personally utilized extremely desk products so I can’t speak on it however their track record is great huge thanks to flexi area for sending this out for review sadly I can not suggest this unit and for the record I’m a hundred percent sure they would have happily replaced the parts that I had an issue with viewing as how both the desktop and the casters got here harmed however from a client viewpoint you ‘d most likely be really excited to get this in