Flexispot Standing Desk Review …Flexispot 32 Desk Riser…
Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are minimal, here are a couple of functions that I wasn’t always a substantial fan of:
The bundle that the desk came in was heavy, so bringing it inside was a group effort, however this is simply a consequence of how tough the Flexispot is.
The practical cable tray was a little bit complicated to install. In the end, you ultimately slip it under screws, which wasn’t really clear from the directions.
You will need to purchase an anti-fatigue mat to remain comfortable, but this is a great idea for any standing desks, so I can’t fault Flexispot for that.
When it arrived and I saw how heavy it was, I was both fired up (considering that this indicated it was going to be durable) and likewise a little hesitant (since we all know just how much of a difficulty putting together furniture can be).
Fortunately, with the help of an instructional YouTube link, it took me only around 42 minutes to put together. Scratch that, it took my 11-year-old daughter, with some guidance from me, from start to finish. The only problem I have with assembly was the cable tray, which I found wasn’t described well in the guidelines.
Once assembled, I love the streamlined look of this desk. I’m positive any of the many diverse surfaces that it is available in would look excellent in any workplace, and the adjustable width makes it simple to fit it in even the smallest of office.
The quiet operation and height memory settings make it simple, efficient, and peaceful to switch between sitting and standing as often times as you want throughout the day.
Finally, this desk is sturdy. It can hold up to 335 lbs even while in operation, so if you have a substantial home computer (or wish to rest on it for some reason) it has you covered. It will also uniformly distribute weight no matter how unbalanced the weight you put on it is, it will not wobble or wiggle.
in that video is pretty kitted out as the desk we’re looking at today is quite fundamental I tried to get as close to that as I could on uplifts site with similar configurations the flexi area desk we’re taking a look at today will run you about four hundred and 10 dollars versus six hundred and fifty for a comparable desk from uplift I try to get as close as possible with the uplift model is in fact 5 inches longer however you can do a lot with five inches boom yes now for transparency flexi area did send this desk out for review but as you need to understand by now doesn’t impact my review in any way the desktop here is 55 inches broad 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not delivering till the end of April at the earliest the desktop is an inch thick however it’s this fundamental laminate as you can potentially get doing not have even any cable television grommets for go through the outside carton
for the desktop was not damaged in any way which is entirely bizarre because I could shoot a 30-second b-roll montage of just the damage and defects on this desktop scuffed scraped pitted just super rough guy if I had actually bought this I ‘d have been on the phone with client service instantly they did also handled to miss out on drilling the pilot holes where you can attach the control box to the desktop a lot of having to do that myself without unintentionally drilling through the opposite of the desktop so yeah pilot holes in wood screws is how you’re gon na be attaching the surface area to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from needing to drill that top was really quite uncomplicated the entire thing came together in about 45 minutes and despite the fact that there’s cable televisions running to it from each component to support motorized function oddly absolutely where any kind of cable management products whatsoever the frame on this system is a single motor dual phase style versus the dual motor three-stage design that comes requirement with the uplift desk this can be upgraded too to both the dual phase double motor and a three-stage dual motor which pushes the cost of the desk up
an additional 70 bucks the frame is created for a max load of 154 pounds and it moves at a rate at an inch per 2nd the height can range from just under 28 inches to simply over forty seven point 6 inches so a max I ‘d it is more than high sufficient even for me and I stay at 6 foot for this design does come basic with the control panel that permits up-and-down movement plus 3 memory areas with an LED readout to tell you the desk height the single motor style uses this drive shaft assembly which has to be changed as the width of the desk is changed the motor operation itself while it might be slow is really peaceful as in barely audible this outside a cost would be the one advantage I would give this system over the uplift desk and I want to be careful here due to the fact that this isn’t a hit piece this desk is 240 dollars more affordable than the comparable uplift model over 35% cheaper even if you upgrade this flexi area test to the double motor three-stage design it still can be found in a hundred and seventy dollars less expensive than the uplift but more affordable does not suggest low-cost this desk is still over four hundred dollars if I had actually paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is solid even if max height I’ll absolutely give it that but the lateral stability of this desk the horizontal motion at this price point it’s unacceptable it’s add fuel to the fire here they include a little safety baffle this little steel piece that mounts to the frame and covers a part of this turning driveshaft when
this desk sees any lateral movement at all the drive shaft hits this baffle and the noise is absolutely frustrating to top things off I decided to include rolling casters to this desk this was a $30 upgrade and two of those 4 casters showed up harmed as well my prepare for this desk at this point is to lose the desk top and came with entirely and replace it with a white laminate lemon table from Ikea and utilize it as an adjustable image table which you can’t do this frame will accommodate desktops as much as 63 inches broad and 31 and a half inches deep so this will roll around the studio make it much easier to film items without having to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I discovered uplift first that is a financial investment in quality office furnishings that will last you this at best feels like a less expensive imitation of that it just doesn’t feel quality and the distinction in between this desk and my main desk is night and day do feel free to have a look at their website as well which likewise feels strangely comparable to among their rivals there’s a wealth of accessories you can get for the flexi spot desk up to and consisting of a foot massager and even a stationary stationary bicycle and I might invest another 10 minutes of our valuable time covering numerous alternatives and devices I might however I believe I’m happier that they just sent out a fundamental desk because as a fundamental desk I’m not a fan of the quality assurance at this rate point and I don’t think slapping on a bunch of bonus is the move when the core product isn’t what it need to be they do provide a 30-day trial if you’re simply morbidly curious and they guarantee their desks for 3 years extremely desk is five years and uplift desk is 7 years if you are Flexispot 32 Desk Riser
in the market for a sit-stand desk they’re incredible mine’s been a life changer for me both in regards to video gaming and productivity however I would invest the extra money it’s gon na take to enter into a greater end producer like uplift desk or extremely desk and I haven’t personally used extremely desk products so I can’t speak on it but their track record is great huge thanks to flexi spot for sending this out for evaluation unfortunately I can not suggest this unit and for the record I’m a hundred percent sure they would have gladly changed the parts that I had a concern with viewing as how both the desktop and the casters arrived damaged however from a client standpoint you ‘d probably be really excited to get this in